工地電梯門套的施工與保養直接關系到建筑的整體美觀度與使用壽命。為了確保工程質量，在施工和后期養護環節需要重點關注以下幾個方面：

The construction and maintenance of elevator door frames on construction sites are directly related to the overall aesthetics and service life of the building. In order to ensure the quality of the project, the following aspects need to be focused on during construction and post maintenance:

一、 施工安裝注意事項

1、 Construction and installation precautions

1. 施工前準備與測量

1. Preparation and measurement before construction

在安裝前，必須確保電梯門框施工已完成，且成品燈盒的管線已鋪設到位2。精準測量是施工的基礎，需對門洞的高度、寬度及墻體厚度進行三維復尺，并彈好控制線，確保門套的垂直度與水平度誤差控制在2mm以內8。

Before installation, it is necessary to ensure that the construction of the elevator door frame has been completed and the pipelines of the finished light box have been laid in place. Accurate measurement is the foundation of construction, which requires a three-dimensional re measurement of the height, width, and wall thickness of the door opening, and the use of control lines to ensure that the verticality and levelness errors of the door frame are controlled within 2mm.

2. 核心安裝工藝

2. Core installation process

間隙預留：門套與電梯門之間必須預留3-5mm的間隙，以防止電梯門在開關時產生摩擦或異響6。

Gap reservation: A gap of 3-5mm must be reserved between the door frame and the elevator door to prevent friction or abnormal noise when the elevator door is opened or closed.

固定方式：不銹鋼門套必須使用專用結構膠進行粘貼固定，這是防止后期脫落的關鍵2。若是石材門套，應采用干掛工藝，并使用專用AB膠加固，嚴禁采用普通水泥濕貼或僅用云石膠點粘。

Fixing method: Stainless steel door frames must be glued and fixed with specialized structural adhesive, which is the key to preventing them from falling off later. If it is a stone door frame, dry hanging technology should be used and special AB glue should be used for reinforcement. It is strictly prohibited to use ordinary cement wet pasting or only use marble glue for point sticking.

接縫處理：線條拼接通常采用45度對角拼接，需使用專業切角機裁切，確保碰角嚴密、平整，縫隙內不留余膠6。

Seam treatment: Line splicing usually adopts 45 degree diagonal splicing, which requires the use of a professional angle cutting machine to cut, ensuring tight and smooth collision angles, and leaving no residual glue in the gaps.

3. 施工安全與成品保護

3. Construction safety and finished product protection

施工人員必須佩戴安全帽、安全帶等防護裝備，防止機具或材料墜落7。

Construction personnel must wear protective equipment such as helmets and safety belts to prevent machinery or materials from falling.

安裝完成后需立即進行成品保護。不銹鋼表面的保護膜在交付前不得私自撕除；石材門套易磕碰的棱角處需用硬質瓦楞板做護角保護，表面覆蓋塑料薄膜，以防其他工種交叉施工時造成劃傷或污染2。

After installation, finished product protection should be carried out immediately. The protective film on the surface of stainless steel shall not be removed without authorization before delivery; The edges and corners of stone door frames that are prone to collision should be protected with hard corrugated boards and covered with plastic film to prevent scratches or pollution caused by cross construction of other trades.

二、 后期保養與維護須知

2、 Post maintenance and upkeep instructions

電梯門套的保養需根據具體材質“對癥下藥”，錯誤的清潔方式會嚴重損害門套表面：

The maintenance of elevator door frames should be tailored to the specific material, and incorrect cleaning methods can seriously damage the surface of the door frames

1. 不銹鋼門套保養

1. Maintenance of stainless steel door frames

清潔手法：清潔時必須順著不銹鋼的發紋方向（通常為豎向）擦拭，嚴禁打圈或左右橫向擦拭，以免破壞表面紋理并留下劃痕9。

Cleaning method: When cleaning, it is necessary to wipe along the direction of the stainless steel hairline (usually vertical), and it is strictly prohibited to circle or wipe horizontally to avoid damaging the surface texture and leaving scratches.

清潔劑選擇：日常可用中性清潔劑或專用不銹鋼保養劑；鏡面不銹鋼建議使用優質玻璃清潔劑。嚴禁使用酸性、堿性或研磨性清潔劑10。

Cleaning agent selection: Neutral cleaning agents or specialized stainless steel maintenance agents can be used for daily use; It is recommended to use high-quality glass cleaner for mirror stainless steel. It is strictly prohibited to use acidic, alkaline, or abrasive cleaners.

定期養護：建議每季度或半年進行一次整體保養，噴灑保養劑后用防滑傷的軟毛巾擦拭，保持光亮并防止氧化生銹9。

Regular maintenance: It is recommended to perform overall maintenance once every quarter or half a year. After spraying maintenance agent, wipe with a soft towel that is non slip to maintain brightness and prevent oxidation and rusting.

2. 石塑/石材門套保養

2. Stone plastic/stone door frame maintenance

日常清潔：石塑門套具有防水防潮功能，日常可用清水或中性洗潔精配合軟毛刷、毛巾擦洗1。

Daily cleaning: The stone plastic door frame has waterproof and moisture-proof functions, and can be cleaned with clean water or neutral detergent combined with a soft brush and towel for daily use.

禁忌操作：絕對不要使用金屬清潔球或小刀刮刻頑固污漬；嚴禁使用醋或其他酸性產品清潔，以免導致門套失去光澤或腐蝕1。

Forbidden operation: Never use metal cleaning balls or knives to scratch stubborn stains; It is strictly prohibited to use vinegar or other acidic products for cleaning to avoid causing the door frame to lose its luster or corrode.

環境控制：避免重物或銳器碰撞；避免長時間陽光暴曬或接觸高溫熱源，以防材料老化、開裂或變形；如有水漬或油污濺灑，需及時用溫水擦凈并擦干3。

Environmental control: Avoid collisions with heavy objects or sharp objects; Avoid prolonged exposure to sunlight or high temperature heat sources to prevent material aging, cracking, or deformation; If there are water stains or oil spills, they should be wiped clean with warm water and wiped dry in a timely manner.